If you are a headlight nerd, this one is for you. We get asked all the time how we at Headlight Revolution actually compare one headlight to another in those shootout videos. You have seen us line up a 4Runner housing against a dozen competitors, but we rarely show the down and dirty details of how the testing really happens, because honestly, it is complicated. So today we are pulling back the curtain on the Morimoto multi-point testing system, the exact method we use to rank low beam and high beam performance. If you want a deeper understanding of how a real bi-LED projector comparison should be done, grab a coffee and settle in.
Why We Stopped Judging Headlights by the Wall
For years the automotive lighting industry has evaluated headlights based on how the beam pattern looks on a wall. That approach has a big problem. Headlights are not designed to illuminate walls, they are designed to illuminate the road. A pretty pattern projected onto drywall tells you very little about how usable that light will be when you are driving at speed on a dark highway. That is exactly the gap the Morimoto multi-point method was built to close.
We want to be clear and transparent with you. Yoshi Ishida, who designs the headlight housings, works for Morimoto Lighting, and Headlight Revolution is owned by the same organization that owns Morimoto. That said, I call Yoshi on a near daily basis to pull information from him so these videos can be as thorough as possible. The goal is not just to find out what is brightest. The goal is to find the headlight that delivers the most comfort and the best overall usability. If you want to see how Morimoto describes their own LED headlight comparison method, it is worth reading alongside our testing breakdown.
Eight Points Out of Twenty-Three
Official regulation is based on 23 points on a test wall. That is a lot of data. The Morimoto multi-point testing system takes the most important eight of those points and uses them to score a headlight. Beyond just a singular measurement at the hot spot, which really tells you nothing about width, balance, or overall performance, this method looks at how the whole beam behaves. Bright spot beams do not make a great headlight, now do they?
The key idea is balance. The balance of intensity from one point in the beam to another greatly influences the behavior of the human eye and therefore our perception of what is ahead. As an example, if the light projected on the ground directly in front of you is too bright relative to the light projected in the distance, the retina in your eyes closes down, reducing your ability to see effectively in the distance. High numbers across the board do not necessarily equal a high score in the real world. This is the heart of proper headlight beam pattern testing.
Getting the Aim Right First
Before we record a single number, we have to nail the aim. If you do not get the aiming right, you will not get the numbers right. We use a laser level to establish the HV points, the horizontal and vertical reference points on the wall. When you turn off the low beam and use the laser level, you can map out exactly where the beam needs to sit.

With the low beam on, you get your vertical aim so you can set it properly. Then with the high beam on, you will notice the center of the high beam lands right on the vertical axis. That is how you confirm your aim is correct. The laser level is just for imagery during the demonstration, we do not actually use it while recording the numbers, but it helps you visualize the process. Once the aim is completely dialed in, then and only then do we start collecting data.
Measuring With Eight Lux Meters
Behind the scenes we have a wall with eight digital lux meters set up at the points that matter most for the multi-point system. There are markings on the wall for all 23 regulatory points, but the ones we are most concerned about are the selected eight.

These housings are also tested by a third party before we do the overview comparison videos. I even have my buddy Jimmy, who is a lot smarter than me, handle a good chunk of the testing. We want the numbers to be as defensible as possible, which is why the whole process leans on the regulated points rather than opinion.
What Each Test Point Measures
Here is the breakdown of what each point tells us:
- Test point 1 measures illuminance at the peak of the beam on your side of the road, equating to distance performance.
- Test point 2 measures illuminance at the peak of the beam on the oncoming traffic side, equating to distance performance.
- Test point 3 measures illuminance in the central part of your beam, equating to general comfort in the midfield.
- Test point 4 measures illuminance out toward the sides of the beam, equating to general comfort to the left and right.
- Test point 5 measures illuminance at the far edges of the beam, equating to width in the distance.
- Test point 6 measures illuminance at the far edges of the beam, equating to width in the near field.
- Test point 7 measures illuminance in front of the hot spot of the high beam, equating to distance and reach.
- Test point 8 measures illuminance in the foreground, where if it is too bright relative to other points it will actually reduce the overall score.
When we measure low beam, we use points 1 through 6 along the wall. For high beam, we use point 7, H2, and point 8. That combination lets us tell the full story of a housing, from reach down the road to how the near field is managed.
The Test Sample: A Morimoto XB Evo 370Z Headlight
For the demonstration, we used a low beam housing, specifically a Morimoto XB Evo headlight built for the Nissan 370Z. It is a great example because it shows how a properly designed housing behaves across every test point.

One detail worth calling out on this housing: Morimoto created a small dip in the beam cutoff to stay in compliance, but then raised the light back up on the left side. That means you still stay compliant while gaining noticeably more light on the left side of the beam pattern. Many other housings simply cut the beam down to avoid being too bright, then get lazy and waste the rest of the projector by chopping the output off. If you are legally able to raise the light to put more usable output down the road, you might as well.
From Candela on the Wall to Lux on the Road
Here is the part that separates this method from everything else. In our comparison videos, we are not just using lux. We collect every number from every point for both low beam and high beam in Candela, using a driver side headlight from every manufacturer we can get our hands on. Then we send those numbers, along with a photo of each housing, over to Yoshi in California where he runs the math.
The measurements from a specific test point on the 2D wall are translated into the target 3D road surface, where they undergo another layer of data processing from Candela to Lux. This translated road surface mapping is the key determining factor in how headlights compare to one another. It takes into account all of the objective measurements and, crucially, how those measurements compare relative to one another. The result is a number nobody can truly dispute because it is built from the eight regulated points. You can explore how this plays out across different housings in our ongoing bi-LED projector comparison coverage.
Compliance Is Not Optional
Another big factor when buying a headlight housing is whether it is compliant. If it is not in compliance, you are probably blinding oncoming drivers. Every single one of these eight points is regulated, which means each point has both a minimum and a maximum candela rating. The reading has to fall within those limits for the headlight to be DOT compliant. This is why a housing that simply dumps maximum brightness everywhere can actually fail, while a balanced housing passes. Our full library of headlight beam pattern testing shows how often this trips up budget products.
Why Height Is Standardized at 0.85 Meters
Distance performance ties directly to mounting height. On the test table in Jimmy’s warehouse, every housing is measured at 0.85 meters high. That is a fixed benchmark. It lets us take a Corvette headlight that sits an inch and a half off the floor and compare it apples to apples with a Jeep or Bronco headlight that normally rides much higher. You put them both on the table at the same height, run the same test, and get a matchable number.
Real world aiming is a different story and depends on how tall your vehicle is. If you have a lifted Tacoma or Jeep that sits over 39.5 inches tall, you would measure on the wall 3 inches down from the dimple in the center of the housing, and that can drastically change the distance at which your light is even usable. Newer vehicles are trending toward lower mounted headlights for exactly this reason. Look at how low the Cybertruck headlights sit. A lower housing makes it easier to get more usable light output down the road, rather than shooting straight down from up high.
Proper Real-World Aiming Reference
If you want to aim your own headlights correctly, the short version is this. Park your vehicle 25 feet from a wall and measure from the ground to the optical center of the outermost projector:
- If that height is less than 34.5 inches, set the top of the cutoff level with your headlight measurement.
- If the height is between 35 and 39 inches, set the cutoff 2 inches below your measurement.
- If the height is greater than 39.5 inches, set the cutoff 3 inches below your measurement.
Reading High Beam Performance
For high beam scoring, we lean on point 7, H2, and point 8. In the 2D driver’s view, points 1 and 2 appear to have a very small visual impact, yet they are actually crucial for focusing on the highway ahead of you.

When those spots are projected onto the ground, the coverage area they represent is far larger than it looks on the wall. Many enthusiasts get misled by the strong visual impression of the foreground zone, but the foreground does not actually cover much of the road. You can dig into Morimoto multi-point testing resources from The Retrofit Source if you want to see more examples of this translation in action: Morimoto multi-point testing.
Foreground: The Make or Break Factor
Arguably, foreground brightness is where a housing is made or broken. The perceived brightness of distant points is strongly influenced by the brightness of nearby objects. It is more important to consider what surrounds the focal point and how it complements it, rather than fixating on the absolute brightness value.

This is where the distance to foreground ratio comes in. It is calculated by dividing the average illumination value of the distance zone by the illuminance of the foreground zone, and it tells us whether excessive foreground brightness is overwhelming your perception of distance lighting. We also use the foreground to mid-distance ratio (FMR) to add further insight into overall beam quality. For more technical background from the team that developed this approach, see the Morimoto multi-point testing system breakdown.
Sample A Versus Sample B
To make this tangible, consider a comparison between two samples. Sample A represents the base reference level of illumination balance. Sample B has excessive foreground illumination added but identical distance zone illumination. When you switch to Sample B, it presents a much stronger illumination impression at first.
But because foreground illuminance dominates the driver’s field of view, that heightened impression quickly becomes the norm. The distance zone, which has the exact same illumination strength as Sample A, loses its significance. The driver’s focus settles on the visually dominant foreground zone and the distance lighting effectively disappears from perception. That is why a headlight that simply looks brighter up front is not necessarily a better headlight. To explore the engineering philosophy further, Morimoto’s own writeups on their LED headlight comparison method pair nicely with these examples.
Why This Matters When You Buy
The overall score we assign is a summary of the minimally selected performances. Seeing the same score on another sample does not mean the two housings perform identically. Some lamps earn their impression with exceptional highlights, while others achieve it through overall balance. A low score can indicate poor balance, a lack of illumination strength, or a combination of both. The best way to use this evaluator is to understand the beam characteristics, not just chase one big number. That is the whole point of testing eight regulated points instead of staring at a single hot spot on a wall.
Frequently Asked Questions
What is the Morimoto multi-point testing system?
It is a headlight evaluation method developed by Yoshi Ishida that measures 8 key points on a test wall (out of the 23 points used in official regulation) to score a headlight’s low beam and high beam balance rather than just its brightest hot spot.
Why not just compare headlights by their brightest spot on a wall?
A single bright hot spot measurement ignores width, balance, and overall usability. As we explain, bright spot beams do not make a great headlight, and balance across multiple points better predicts real-world performance.
How are the wall measurements converted for real-world comparison?
Measurements are first taken in Candela at each test point on the 2D wall, then processed and translated into Lux on a simulated 3D road surface, which is the key factor in comparing headlights to one another.
At what height are headlights mounted for this testing?
All headlights are tested at a standardized 0.85 meter height on the wall so that housings from very different vehicles, like a Corvette versus a lifted Jeep, can be compared on equal footing.
What is the distance to foreground ratio and why does it matter?
It is a calculation dividing the average illumination of the distance zone by the illuminance of the foreground zone, used to determine if excessive foreground brightness is overwhelming a driver’s perception of distance lighting, which is a make or break factor for housings.
Meet the Experts Behind Headlight Revolution
Chris Nelson – Founder
Before founding Headlight Revolution in 2011, Chris worked as an automotive install technician specializing in lighting, sound systems, and engine performance parts. He has personally tested thousands of lighting products and works directly with lighting engineers to evaluate the technical performance behind every recommendation.
Josh Beberg – Content Production Manager
Josh leads hands-on testing and content production at Headlight Revolution. From beam pattern comparisons to real-world installations, he works directly with lighting engineers to ensure every review is grounded in measured results, not marketing specs.











