2014-2015 GMC Sierra HID Headlights Install Guide

2014-2015 GMC Sierra factory headlight before HID conversion

The 2014 and 2015 GMC Sierra comes from the factory with cool-looking projector headlights and daytime running lights on the top and bottom, but it uses a 55 watt H11 halogen bulb that honestly is not that great. In this guide, we are going to walk you through the simple process of increasing your light output by a massive amount using the right parts for the job. We tested and installed the all-new GTR Lighting Gen 5 PWM CANbus HID ballast kit, and it makes adding HIDs to your truck about as easy as installing a normal HID conversion kit. Here is exactly how we did it, what to watch out for, and why these particular GMC Sierra HID headlights work when ordinary kits fail.

Why Ordinary HID Kits Fail on the 2014-2015 GMC Sierra

The frustrating part about these trucks is that you cannot just drop in any old HID kit and expect it to work. The GMC Sierra of this vintage uses a CANbus and pulse width modulation (PWM) system to control the headlights. That means if you install a standard HID kit, it works fine with the key off, but the moment you start the engine it flickers and shuts off. We have seen this happen countless times, and it drives people crazy because the parts seem fine until the truck is actually running.

That is where the GTR Lighting Gen 5 ballast comes in. It is a 55 watt ballast producing 5,000 lumens of light per bulb, which is five times brighter (500% brighter) than your original halogen bulb. The Gen 5 has a smart PWM and CANbus system built in that is plug and play for a 55 watt setup on the GMC Sierra, so it eliminates the flicker and shutdown problem entirely. If you want to browse other options for your rig, we keep a full selection of HID conversion kits for trucks and cars so you can match the right ballast technology to your vehicle.

What Comes in the GTR Lighting Gen 5 Kit

When you open the box, you get a few smaller boxes and a few brackets. One box holds the bulbs, and these are really nice bulbs with high-temp wiring, precise fitting bases with nice O-rings, and beautiful color. Out of all the HID kits we have ever used, we find the bulbs that come with the GTR Lighting HID conversion kits are among the brightest with the best colors.

GTR Lighting Gen 5 PWM CANbus HID ballast kit contents with bulbs and brackets
Inside the GTR Lighting Gen 5 kit: HID bulbs, ballasts, and mounting brackets.

Color temperature matters a lot here. When you climb up to 6000K or 8000K, you can get greenish hues that we do not like to see. The GTR Lighting 5000K HID bulbs produce a perfectly pure white, and that white matches the color of your factory daytime running lights. That color match is a big deal for the final look because mismatched DRLs and headlights look like an afterthought.

About the Gen 5 Ballast Itself

The Gen 5 is a super slim ballast with the smart PWM and CANbus system built in, and it is plug and play for a 55 watt setup on the Sierra. It also has a built-in EMC filter, so you do not get funny things like radio noise. This is one of the fastest-starting ballasts we have tested, and on the Sierra it is a perfect fit.

If you are comparing ballast families, we have also covered the GTR Lighting 35W Ultra Series ballast for folks who want a lower-wattage option, and if you prefer a complete bolt-in assembly over a conversion kit, the GMC Sierra Morimoto Elite HID system is worth a look. Those who like to source directly can also check out the H11 GTR Lighting Ultra Series HID kit or the Morimoto H11 Elite HID system for additional comparison.

How the HID Bulb Replaces the Factory Halogen

These HID bulbs are designed as a direct swap. When you take out the old halogen bulb, the new one fits right in place. The three alignment tabs mimic the same style and position as your original halogen bulb, so you untwist the old one and twist in the new one. The HID wiring connects right where the original halogen bulb used to plug in, because that connector looks exactly like the socket on the old halogen bulb. One side of the dust cover holds the bulb wiring, and the other side plugs directly into the Gen 5 ballast. It only goes in one way, so there is no guessing.

Step-by-Step Install Guide

We are going to show you the full install the way we did it on the truck. For the sake of filming, we put the camera in the engine bay so you can see what is happening behind the headlight, so keep that in mind as you follow along.

Step 1: Remove the Dust Cover

On the back of the headlight you will find a dust cover. On the driver side, turn the dust cover counterclockwise and pull it out. Inside you will see the light bulb with a two-pin connector and some wiring.

Removing the dust cover from the GMC Sierra headlight housing
Twisting off the dust cover to access the factory H11 halogen bulb.

To remove the connector, just lift up on the tab with your thumb or finger. It pops up pretty easily. Pull the bulb away and you will be left with your connector.

Step 2: Drill the 7/8 Inch Hole

Decide where your light bulb will fit behind the dust cover, and drill the hole near that point. We use a tool called a unibit, or step bit, which cuts progressively larger holes. We are shooting for a 7/8 inch hole, which is almost a full inch. If you go a full inch it will still work, but your seal will not be quite as tight. You want the smallest hole possible in the dust cover for the best seal.

Drilling a 7/8 inch hole in the headlight dust cover with a step bit
Using a step bit to drill a 7/8 inch hole for the HID wiring pass-through.

Use common sense so you do not hurt yourself or damage your table. If you cannot do this safely, do not do it. Three quarters of an inch is too small, a full inch is okay, and 7/8 of an inch is really the perfect size for almost any HID conversion kit. The purpose of drilling the hole is to pass half of the wiring through the dust cover to the outside of the headlight housing while preserving the function of the dust cover. The cover keeps dust, moisture, bugs, and animals out of your headlight, so keeping that weatherproof seal tight matters.

Step 3: Disassemble the HID Connector

The connector that plugs into your ballast is too big to fit through a 7/8 inch hole, so we take it apart. There are basically two steps. First, along the bottom of the connector there is a retaining clip held by a shoulder on each side. Using a small screwdriver or pick tool, release that clip from the shoulders.

Using a terminal release tool to disassemble the HID connector pins
A terminal release tool separates the connector pins so the wiring can pass through the drilled hole.

To remove the pins, you could use a really small flat jeweler’s screwdriver or a pick tool, but we use a purpose-built tool: the OTC part number 4461 terminal release tool set. Examine the top of the HID connector, which is shaped like a T. On the bottom portion of the T there is a slot where the pick tool goes in. Rest the pick on the correct side, go down to about the bottom of the travel without forcing it, push it toward the outside to depress the internal spring lever, hold everything in place, and remove the wire. Important note: before you take it apart, examine the orientation of the wires, take a picture, and write some notes so you put it back together exactly the same way.

Step 4: Pass the Wiring and Seal the Grommet

With the bulky connector off, you can easily pass the wiring through the dust cover. Pull it all through, then use the rubber grommet, which has a recessed slot all the way around, to fill the gap in the hole you drilled. It will not simply drop through, so carefully fold the flaps of the grommet around until they sandwich on the outside of the hole, and work it around in a circle until the whole thing pops into place.

Rubber grommet sealing the drilled hole in the dust cover
The rubber grommet folds into place to reseal the dust cover around the new wiring.

Give it a tug to seat it. You should see the lip completely covering the hole on both sides. Now reassemble the connector using your notes and photo. When you push each wire in, you want to hear an audible click. If you do not hear that click, or you tug and the wires pop out, the spring release lever needs help. Pull it out, reset that spring lever, and reinsert. Then put the retaining clip back on and you are ready.

Step 5: Install the HID Bulb

Put the HID bulb right back where the factory halogen bulb was and turn it clockwise. It is a tight fit, but it seats using the same alignment tabs. Connect the little harness to the factory harness and make sure red matches up to red.

Installing the HID bulb into the GMC Sierra headlight housing
The HID bulb twists into the factory H11 location using the same alignment tabs.

With that done, tuck the slack into the headlight and reattach the dust cover. The dust cover has little slots that line up in the headlight, so set it in and turn it clockwise to lock it.

Step 6: Mount the Gen 5 Ballast

Attach the ballast to the mounting bracket it comes with. The ballast includes slick metal cages: put in one side, clip it in, and remove the tape on the backside to stick it to a clean flat surface. If you have a diesel engine or dual batteries, there is plenty of room above the secondary battery.

GTR Lighting Gen 5 ballast mounted in the GMC Sierra engine bay
The Gen 5 ballast mounts with its metal cage, double-sided tape, and a grounding strap.

The kit includes a white ground strap wire. The idea is that if you ground the bracket (which is touching the ballast), you ground the ballast. Grounding the ballast ensures proper electrical function, eliminates radio interference, and makes everything work better overall. Plug the power harness for the ballast into the harness you ran outside the dust cover, make your connections, and that is it. Zip tie and tidy up the wiring however you see fit, then test everything before buttoning up.

Step 7: Repeat on the Passenger Side

The passenger side is the exact same process, with one difference: you have to remove the airbox. That is not a big deal. Just undo the hose clamp for the hose, and the airbox pops right up and out of the way so you can access the headlight the same way as the driver side.

Our Honest Take on These GMC Sierra HID Headlights

This install does not have to be tough if you use the right parts. The new GTR Lighting Gen 5 PWM and CANbus module is a 55 watt ballast that is totally plug and play on the Sierra, so you get a big jump in light output, better style, and the ability to see where you are going better at night all the time. The 5000K color matching your DRLs ties the whole front end together, and the built-in EMC filter keeps your radio quiet.

One thing worth keeping in mind with any HID setup is long-term performance. If you want to understand what to expect down the road, we broke down how HID bulbs degrade over time so you know when it might be time to refresh your bulbs. For a truck that started life with mediocre halogen output, this upgrade is a serious, worthwhile improvement.

Frequently Asked Questions

Why do normal HID kits flicker or shut off in a 2014-2015 GMC Sierra?

These trucks use a CANbus and pulse width modulation (PWM) system to control the headlights, so a standard HID kit works with the key off but flickers and shuts down once the engine starts.

What ballast solves the flicker problem on the GMC Sierra?

The GTR Lighting Gen 5 PWM CANbus HID ballast is built specifically to be plug and play on the Sierra’s PWM/CANbus headlight circuit, eliminating the flicker and shutdown issue.

What bulb size does the 2014-2015 GMC Sierra headlight use?

The factory projector headlights use a 55 watt H11 halogen bulb, which is replaced in this kit by an HID bulb with matching alignment tabs for a direct fit.

How much brighter is the HID kit than the factory halogen bulb?

The GTR Lighting Gen 5 ballast and bulb combination produces 5,000 lumens per bulb, which is described in the video as 500% brighter than the original 55 watt halogen bulb.

How do you route the HID wiring without ruining the dust cover seal?

You drill a 7/8 inch hole in the dust cover, disassemble the bulky HID connector with a terminal release tool to pass the wires through, then reassemble the connector and seal the hole with the included rubber grommet.


Meet the Experts Behind Headlight Revolution

Chris Nelson, Founder of Headlight Revolution

Chris Nelson – Founder
Before founding Headlight Revolution in 2011, Chris worked as an automotive install technician specializing in lighting, sound systems, and engine performance parts. He has personally tested thousands of lighting products and works directly with lighting engineers to evaluate the technical performance behind every recommendation.

Josh Beberg, Content Production Manager at Headlight Revolution

Josh Beberg – Content Production Manager
Josh leads hands-on testing and content production at Headlight Revolution. From beam pattern comparisons to real-world installations, he works directly with lighting engineers to ensure every review is grounded in measured results, not marketing specs.